|
|
Ascend disconnect/Progress codes
Disconnect Reason progress codes
03 Call Disconnected
04 CLID Authentication Failed
05 CLID Radius Timeout
10 Modem never detected DCD call up
20 TermSrv - user quit
11 The modem detected Usually caused by UART ERRORS for
DCD, but it became external modems, or win 3.1 with
inactive modem that are faster than 19.2k
(LOST CARRIER). (windows only support up to 19.2k)
To fix it, lower port speed.
21 The sessions timed The user was disconnected for inactivity
out because there was it looks like it is set to 30 mins now,
no activity on a PPP but it actually disconnects after 12-20
link. minutes.
23 PPP connection could It's a misconfiguration in the ASCEND
start because the caused by too many PRI's for not enough
remote host had no IP IP addresses, we've recently seen this
address set up, or the with the Sault Ste Marie ascend.
dynamic pool could not If you ever see this, contact dataops
assign one. or me and I'll check the box's config.
(TermSrv - no IP Addr)
24 TermSrv - exit Raw TCP
25 TermSrv - login failed
26 TermSrv - Raw TCP disabled
27 TermSrv - CTRL-C during login
31 TermSrv - exit Rlogin Modem awaiting DCD
32 TermSrv - bad Rlogin option Modem awaiting Codes
33 TermSrv - not enough resources
35 MPP - no NULL msg timeout
40 PPP - LCP Timeout Terminal Server started
41 PPP - LCP Negotiation failed Raw TCP started
Using script to connected
42 PPP - PAP Auth failed Telnet started
43 PPP - CHAP Auth failed Raw TCP connected
44 Authentication failed Radius server is not responding,
from the remote server. is equal to NO REPLY FROM RADIUS SERVER.
45 The peer requested a When a user hits "DISCONNECT" in WIN95
disconnect via PPP. dial-up networking.
Its a normal LCP terminate :) Only
the user's machine can request it.
46 PPP - Receive Close Event Rlogin connected
47 LCP closed because no This means that 1- TCP/IP is not
NCPs were opened. installed or is corrupted.
or that you tried to create a
non-supported network connection:
IPX/SPX or Appletalk or etc.
If you get the error with TCP/Ip
installed and Netbui/SPX... also
installed, you should to remove
everything except Dial-up Adapter
and TCP/IP. (it really works :)
48 PPP - MP bundle unknown
49 PPP - LCP close MP add fail
50 Session Table Full Modem Outdial - Call Up
51 Out of resources
52 Invalid IP Address
53 Hostname resolution failed
54 Bad/missing port number
60 Host Reset LAN Session Up
61 Connection refused Opening LCP
62 Connection timeout Opening CCP
63 Connection Closed Opening IPNCP
64 Network unreachable Opening BNCP
65 Host unreachable LCP Opened
66 Network admin unreachable CCP Opened
67 Host admin unreachable IPNCP Opened
68 Port unreachable BNCP Opened
69 LCP State Initial
70 LCP State Starting
71 LCP State Closed
72 LCP State Stopped
73 LCP State Closing
74 LCP State Stopping
75 LCP State Request Sent
76 LCP State Ack Received
77 LCP State Ack Sent
80 IPXNCP Opened
81 ATNCP Opened
82 BACP Opening
83 BACP Opened
90 V110 Up
91 V110 State Opened
92 V110 State Carrier
93 V110 State Reset
94 V110 State Closed
100 Session Timeout
101 he session failed for Two user connect same
security reasons. server
(Invalid incoming user)
102 Disconnect due to callback
120 Protocol disabled/unsupported
150 Disconnect requested by RADIUS
151 Disconnect by Local Admin Killed concurrent session
160 V110 timeout/sync retry exceed
170 PPP Auth Timeout exceeded
180 user executed Do..Hangup
185 Remote End Hung Up
190 Resource has been Quiesced
195 MAX Call duration reached
|
