Ascend disconnect/Progress codes

            Disconnect Reason                 progress codes


     03     Call Disconnected

     04     CLID Authentication Failed

     05     CLID Radius Timeout

     10     Modem never detected DCD          call up

     20     TermSrv - user quit

     11     The modem detected                Usually caused by UART ERRORS for
            DCD, but it became                external modems, or win 3.1 with
            inactive                          modem that are faster than 19.2k
            (LOST CARRIER).                   (windows only support up to 19.2k)
                                              To fix it, lower port speed.

     21     The sessions timed                The user was disconnected for inactivity
            out because there was             it looks like it is set to 30 mins now,
            no activity on a PPP              but it actually disconnects after 12-20
            link.                             minutes.

     23     PPP connection could              It's a misconfiguration in the ASCEND
            start because the                 caused by too many PRI's for not enough
            remote host had no IP             IP addresses, we've recently seen this
            address set up, or the            with the Sault Ste Marie ascend.
            dynamic pool could not            If you ever see this, contact dataops
            assign one.                       or me and I'll check the box's config.
            (TermSrv - no IP Addr)

     24     TermSrv - exit Raw TCP

     25     TermSrv - login failed

     26     TermSrv - Raw TCP disabled

     27     TermSrv - CTRL-C during login

     31     TermSrv - exit Rlogin             Modem awaiting DCD

     32     TermSrv - bad Rlogin option       Modem awaiting Codes

     33     TermSrv - not enough resources

     35     MPP - no NULL msg timeout

     40     PPP - LCP Timeout                 Terminal Server started

     41     PPP - LCP Negotiation failed      Raw TCP started
                                              Using script to connected

     42     PPP - PAP Auth failed             Telnet started

     43     PPP - CHAP Auth failed            Raw TCP connected


     44     Authentication failed             Radius server is not responding,
            from the remote server.           is equal to NO REPLY FROM RADIUS SERVER.

     45     The peer requested a              When a user hits "DISCONNECT" in WIN95
            disconnect via PPP.               dial-up networking.
                                              Its a normal LCP terminate :) Only
                                              the user's machine can request it.

     46     PPP - Receive Close Event         Rlogin connected

     47     LCP closed because no             This means that 1- TCP/IP is not
            NCPs were opened.                 installed or is corrupted.
                                              or that you tried to create a
                                              non-supported network connection:
                                              IPX/SPX or Appletalk or etc.
                                              If you get the error with TCP/Ip
                                              installed and Netbui/SPX... also
                                              installed, you should to remove
                                              everything except Dial-up Adapter
                                              and TCP/IP. (it really works :)

     48    PPP - MP bundle unknown

     49    PPP - LCP close MP add fail

     50    Session Table Full                 Modem Outdial - Call Up

     51    Out of resources

     52    Invalid IP Address

     53    Hostname resolution failed

     54    Bad/missing port number

     60    Host Reset                         LAN Session Up

     61    Connection refused                 Opening LCP

     62    Connection timeout                 Opening CCP

     63    Connection Closed                  Opening IPNCP

     64    Network unreachable                Opening BNCP

     65    Host unreachable                   LCP Opened

     66    Network admin unreachable          CCP Opened

     67    Host admin unreachable             IPNCP Opened

     68    Port unreachable                   BNCP Opened

     69                                       LCP State Initial

     70                                       LCP State Starting

     71                                       LCP State Closed

     72                                       LCP State Stopped

     73                                       LCP State Closing

     74                                       LCP State Stopping

     75                                       LCP State Request Sent

     76                                       LCP State Ack Received

     77                                       LCP State Ack Sent

     80                                       IPXNCP Opened

     81                                       ATNCP Opened

     82                                       BACP Opening

     83                                       BACP Opened

     90                                       V110 Up

     91                                       V110 State Opened

     92                                       V110 State Carrier
 
     93                                       V110 State Reset

     94                                       V110 State Closed

     100   Session Timeout


     101  he session failed for               Two user connect same
          security reasons.                   server
          (Invalid incoming user)

     102   Disconnect due to callback

     120   Protocol disabled/unsupported

     150   Disconnect requested by RADIUS

     151   Disconnect by Local Admin          Killed concurrent session

     160                                      V110 timeout/sync retry exceed

     170   PPP Auth Timeout exceeded

     180   user executed Do..Hangup

     185   Remote End Hung Up

     190   Resource has been Quiesced

     195   MAX Call duration reached

Manufacturer/Operating System Error Codes